EN ISO11997-1循環腐蝕試驗標準（鹽霧、干燥、潮濕）

時間：2018/11/24閱讀：7856

undefined

L24

Cycle A

C.1 Salt fog test solution

Prepare the spray solution as described in Clause 5 by dissolving sodium chloride in water to give a concentration of (50±10)g/l .The PH of the solution shall be in the range 6 to 7.

C.2 Cycle

Set up the cabinet to perform the following cycle.

Step	Time H	Temp℃	Condition	Notes
1	2	35±2	Salt spray
2	4	60±2	Dry：20-30%
3	2	50±2	Wet：95%RH or over
4	Go back to step 1			This makes a total cycle time of 8h from step1 to step3
	Transtition time（ie time allowed to reach the temperature and relative humidity specified for a condition after changing to that condition）：			From salt spray to dry：within 30min From dry to wet：within 150 min From wet to salt spray：within 30min The effect of the salt spray will，in principle，be instaneous。 For details of drying-air flow，see 6.4
NOTE Set points and operational fluctuations can be listed either independently of each other or in the format：set point±operational fluctuations.The set point is the target condition for the sensor when used at the operational control point as programmed by the user.Operational fluctuations are deviations from the indicated set point at the control point indicated by the readout of the calibrated control sensor during equilibrium operation and do not include measurement uncertainty.At the operational control point , the user programmes that exat number . The operational fluctuations specified for that set point do not imply that the user is allowed to programme a set point higher or lower than the exact set point specified.

C3 Salt fog depsiton rate

The salt fog deposition rate shall be 1ml/h to 2ml/h,when the salt fog iscollected over a 24h period (see Clause 10)

C 4 Duration

Unless otherwise agreed，repeat the test cycle for 30 cycles(240h),60cycles(240h),90cycles(720h) or 180cycles(1440h)

Cycle B

C.1 Salt fog test solution

Prepare the spray solution as described in Clause 5 by dissolving sodium chloride in water to give a concentration of (50±10)g/l .The PH of the solution shall be in the range 6 to 7.

C.2 Cycle

Set up the cabinet to perform the following cycle.

Step	Time	Temp	Condition	notes
1	24	35±2	Salt fog
2	8	40±2	100%RH	Water condensing on test panels
3	16	23±2	（50±20）%RH
4	8	40±2	100%RH	Water condensing on test panels
5	16	23±2	（50±20）%RH
6	8	40±2	100%RH	Water condensing on test panels
7	16	23±2	（50±20）%RH
8	8	40±2	100%RH	Water condensing on test panels
9	16	23±2	（50±20）%RH
10	48	23±2	（50±20）%RH
11	Go back to step 1			This makes the total cycle time 7 days from step1 to step10.
NOTE Set points and operational fluctuations can be listed either independently of each other or in the format：set point±operational fluctuations.The set point is the target condition for the sensor when used at the operational control point as programmed by the user.Operational fluctuations are deviations from the indicated set point at the control point indicated by the readout of the calibrated control sensor during equilibrium operation and do not include measurement uncertainty.At the operational control point , the user programmes that exat number . The operational fluctuations specified for that set point do not imply that the user is allowed to programme a set point higher or lower than the exact set point specified.

C3 Salt fog depsiton rate

The salt fog deposition rate shall be 1ml/h to 2ml/h,when the salt fog iscollected over a 24h period (see Clause 10)

C 4 Duration

Unless otherwise agreed，repeat the test cycle for 840 h

ECS2017_3

Cycle C

C.1 Salt fog test solution

Prepare the spray solution as described in Clause 5 by dissolving sodium chloride in water to give a concentration of (0.31±0.01)g/l and (4.1±0.01)g/l respectively .The PH of the solution shall be in the range 6 to 7.

C.2 Cycle

Set up the cabinet to perform the following cycle.

Step	Time min	Temp ℃	Condition	notes
1	210	30±2	Salt fog
2	210	40±2	Dry	Drying-air purge(see 6.4)
3	1470	40±2	（75±15）%RH	One method of achieving this conditon is to alternate the dry and humid cycles for suitable(short)time periods to keep the RH between the limits specified
4	102	30±2	Dry	Drying-air purge(see 6.4)
5	210	30±2	Salt fog
6	378	30±2	90% to 100%RH	Water condensing on test panel
7	180	35±2	Dry	Drying-air purge(see 6.4)
8	120	25±2	Dry
9	Go back to step 1			This makes the total cycle time 48h from step1 to step8.
NOTE Set points and operational fluctuations can be listed either independently of each other or in the format：set point±operational fluctuations.The set point is the target condition for the sensor when used at the operational control point as programmed by the user.Operational fluctuations are deviations from the indicated set point at the control point indicated by the readout of the calibrated control sensor during equilibrium operation and do not include measurement uncertainty.At the operational control point , the user programmes that exat number . The operational fluctuations specified for that set point do not imply that the user is allowed to programme a set point higher or lower than the exact set point specified.

C3 Salt fog depsiton rate

The salt fog deposition rate shall be 2ml/h to 4ml/h,when the salt fog iscollected over a 24h period (see Clause 10)

C 4 Duration

Unless otherwise agreed，repeat the test cycle for1000h

Cycle D

C.1 Salt fog test solution

Prepare the spray solution as described in Clause 5 by dissolving sodium chloride in water to give a concentration of (50±10)g/l .The PH of the solution shall be in the range 6 to 7.

C.2 Cycle

Set up the cabinet to perform the following cycle.

Step	Time H	Temp℃	Condition	Notes
1	0.5	30±2	Salt spray
2	1.5	30±2	Wet：（95±3）%RH
3	2	50±2	Hot dry
4	2	30±2	Warm dry
5	Go back to step 1			This makes a total cycle time of 6h from step1 to step4
	Transtition time（ie time allowed to reach the temperature and relative humidity specified for a condition after changing to that condition）：			From salt spray to wet：within 10min From wet to hot dry：within 15 min From hot dry to salt warm dry：within 30min From salt warm dry to salt spray：instaneous
NOTE Set points and operational fluctuations can be listed either independently of each other or in the format：set point±operational fluctuations.The set point is the target condition for the sensor when used at the operational control point as programmed by the user.Operational fluctuations are deviations from the indicated set point at the control point indicated by the readout of the calibrated control sensor during equilibrium operation and do not include measurement uncertainty.At the operational control point , the user programmes that exat number . The operational fluctuations specified for that set point do not imply that the user is allowed to programme a set point higher or lower than the exact set point specified.

C3 Salt fog depsiton rate

The salt fog deposition rate shall be 1ml/h to 2ml/h,when the salt fog iscollected over a 24h period (see Clause 10)

C 4 Duration

Unless otherwise agreed，repeat the test cycle for 28 cycles(168h)

狠狠色丁香久久综合婷婷亚洲成人福利在线-欧美日韩在线观看免费-国产99久久久久久免费看-国产欧美在线一区二区三区-欧美精品一区二区三区免费观看-国内精品99亚洲免费高清

EN ISO11997-1循環腐蝕試驗標準（鹽霧、干燥、潮濕）

會員登錄

收藏該商鋪

提示

狠狠色丁香久久综合婷婷亚洲成人福利在线-欧美日韩在线观看免费-国产99久久久久久免费看-国产欧美在线一区二区三区-欧美精品一区二区三区免费观看-国内精品99亚洲免费高清

EN ISO11997-1循環腐蝕試驗標準（鹽霧、干燥、潮濕）

會員登錄

收藏該商鋪

提示

EN ISO11997-1循環腐蝕試驗標準（鹽霧、干燥、潮濕）